联系人: 辽宁销售公司 经理18525626742 吉林销售公司 经理18525626742 内蒙销售公司 经理15909858212 黑龙江销售公司 经理15909858212 沈阳销售公司 经理13889849578 全国其他区域 经理18525626742 电 话:(总部)0411-87313600 邮 箱:sgnt5008@126.com 地 址:总部:辽宁大连开发区 |
HIGH AIR品牌PB10-40A中压空压机HIGH AIR品牌PB10-40A中压空压机 技术资料 PB10-40A (风冷) 汉纬尔机械(上海)有限公司 整机描述 According to your requirements High Air has selected the reciprocating compressor PB10-40 for compression of air with 根据需求,汉纬尔选择的压缩机是PB10-40活塞式压缩机。 a capacity of 10 m³/min at suction pressure of 1 bara 在入口压力1Bara情况下,流量10m³/min and discharge pressure of 40 bar g 排气压力40Bar G可调 for stationary installation. 用于固定安装方式。 The unit will be driven by an electric motor via V-belts. *图片仅供参考 压缩机采用电机驱动,皮带驱动方式。 The cooling system on the compressor consists of air cooling. 压缩机采用风冷冷却方式。 The ambient conditions are: 使用环境条件为: in the range of 0°C / + 45°C max. 温度0°C / + 45°C Humidity < 90% 湿度< 90% The unit is complete assembled on one base frame and will be tested under full load before shipment.and the HIGH AIR-QA-System which has been certified corresponding to ISO 9001. 压缩机组安装在一个撬装底盘上,出厂前经过整体测试。汉纬尔取得ISO9001质量体系认证。 Technical data 技术参数 Compressor Type PB10-40A 压缩机型号 PB10-40A driven via - V-Belts 驱动方式 皮带驱动 cooling - air cooled 冷却方式 风冷 weight - approx. 5000 kg 重量 大约5000 kg dimensions - 尺寸 约3.2*2.3*1.9米 medium - air 压缩介质 空气 capacity (FAD) - 10 m³/min 流量 10 m³/min Inlet pressure - 1 bar a 进气压力 1 bar a inlet temperature - 30 °C 进气温度 30 °C working pressure - 40 bar g 工作压力 40 bar g final gas temperature (downstream aftercooler) - approx. +15 °C above cooling air temp. 最终排气温度(后冷却器之后) 温升+15°C number of stages - 3 压缩级数 3级 number of axes - 6 气缸数 6个 cylinder arranged - Double "W" design 气缸布局 双列W型结构 speed - 960 rpm 转速 960 rpm 电机功率 110 kW Electric drive 110 kW 电机 110 kW type - squirrel cage induction motor 类型 鼠笼式异步电机 转速 1500 rpm 防护等级 IP54/ B3/ Isol F 电压/频率 380V、50赫兹 SCOPE OF SUPPLY 供货范围 1 Compressor PB10-40A 压缩机 PB10-40 COMPRESSOR UNIT, consisting of: 压缩机由以下部分组成 BarE COMPRESOR: 压缩机系统 COMPRESSOR BLOCK: 压缩机主机 Compressor block (crankcase with complete transmission gearing, cylinders, 压缩机主机 cylinder heads and suction/discharge valves) (包含曲轴箱、传动部分、曲轴、连杆、气缸、缸头、活塞及气阀) Fan driven by the crankshaft 风扇 压缩机曲轴驱动 Lubrication Motor driven oil pump, oil-piping, oil level sight glass and 润滑 pressure switch, oil filter 电机驱动润滑油泵,油管路,油位镜和润滑油压力开关,油过滤器 Air inlet filter with exchangeable filter cartridge 进气过滤器 带有可更换的进气滤芯 Inter- & Aftercooler air cooled with separators 级间和后冷却器 风冷,带有汽水分离器 Safety valves spring loaded, after each stage. 安全阀 弹簧式,每级之后 Oil pressure gauge 油压表 Pressure gauge after each stage. 压力表 每级之后 Steel base frame with rubber pads for elastic mounting 钢制底盘 带有橡胶避震脚垫 Automatic condensate drain mounted on the condensate seperatordownstream of the inter- 自动排污阀 and aftercooler 安装在汽水分离器上。 Belt pulley 皮带轮 Belt drive motor belt pulley, V-belt, belt guard and tensioning device 皮带驱动 电机皮带轮,V型皮带,皮带防护罩 Piping complete piping to edge of main frame 管路 压缩机内部全部管路连接 Elastic hose for connection of discharge piping 排气软管 用于连接压缩机排气 Non return valve for mounting in the discharge line 止回阀 安装在压缩机出口 MONITORING EQUIPMENT, consisting of: 监控设备,包含 压力开关,安装在压缩机上,监视压缩机的排气压力 温度RTD,安装在压缩机上,监视压缩机的排气温度 低油压保护开关,安装在油路上 Local instrument panel Pressure gauges – discharge pressure after each stage 就地仪表盘 Pressure gauge- oil pressure 压力表-每级出口压力 压力表-润滑油压力 Including complete mounting, tubing, cabling, painting and testing of the unit in our workshop. 包括全部的安装,管路,电缆,喷漆和工厂测试 2 Electric drive 110 KW 电机 110 KW Electric drive configuration B3, 380 V / 50 Hz, 驱动电机 B3 安装方式,380V,50赫兹 3 Switch Cabinet 控制柜 For monitoring and control of all compressor functions. 用于监视和控制压缩机的所有功能。 Designed with steel-sheet enclosure; protection IP54; control voltage 24 V DC; with built in power- and PLC element; wall fastening and timing relay for alternate condensate drain . 采用钢制外壳,IP54防护等级,控制电压24VDC,内部带有电源及PLC控制模块,变频启动。 Control functions: auto start/stop 控制功能 自动启动、停机 manual start/stop 手动启动、停机 auto drain 自动排污 Shut-downs: compressor final temperature high 停机保护功能 压缩机排气温度过高 compressor oil pressure low 压缩机油压过低 motor over current 电机过载 low cooling water flow 冷却水流量过低 Settings start pressure 设定功能 启动压力 stop pressure 停机压力 auto drain cycle 排污循环时间 drain time 排污时间 Display discharge pressure 显示功能 排气压力 running time 运行时间 shut down indicator 故障指示 status 工作状态 上一篇: 螺杆空压机密码错误怎么办?
下一篇: 哪些企业需要用到空压机?
|